nsd-–-vs-5fxt-1-–-controller-varicam-–-stc-vietnam.png

NSD – VS-5FXT-1 – Bộ điều khiển VARICAM – STC Vietnam

Hãng sản xuất: NSD Vietnam

Nhà cung cấp: STC Vietnam

VS-5F is Standard VARICAM series with cam switch on/off output.

ADVANTAGE

  • Standard feature with 24points of switch on/off signal output (VS-5FX series : Max.40points)
  • Select and control the on/off angle by 0.5°
  • Max.10 points of cam angles can be selected by 1 switch signal
  • Max.0.176ms of signal updating cycle ※
  • User friendly digital function setting and display

When ON / OFF range is 1 degree or more

VS-5F[1][2]-[3]

[1]No. of programs×No. of switch outputs , and others

Code Output code
Blank 1 program×24 switches
D 8 programs×24 switches, current position BCD output.
X 16 programs×40 switches or 32 programs×24 switches, current position BCD output.

[2]Output system

Code Output system
Blank Sink type

[3]Power supply voltage

Code Specification
1 24VDC

General specification

Item Specification
Converter model VS-5F-1 VS-5FD-1 VS-5FX-1
Power supply voltage 24VDC
Permissible power
voltage range
21.6 ~ 30VDC
Power consumption 10W or less
Insulation resistance 20MΩ or more between external DC power terminals and ground
(by 500 VDC insulation resistance tester)
Withstand voltage 500 VAC, 60Hz for 1 minute
between external DC power terminals and ground
Vibration resistance 20m/s2 10 ~ 500Hz, 10cycles of 5 minutes in 3 directions,
conforms to JIS C 0040 standard
Ambient operating
temperature
0 ~ +55℃ (No freezing)
(Surrounding air temperature rating of 55℃ maximum)
Ambient operating
humidity
20 ~ 90 %RH (No condensation)
Ambient operating
environment
Free from corrosive gases and excessive dust
Ambient storage
temperature
-10 ~ +70℃
Grounding Must be securely grounded (ground resistance of 100 ohm or less)
Construction Inside control panel
Mounting Select from two-screw mounting/DIN rail installation/
on-panel mounting using panel mounting fixture VS-K-F.
Outside dimension (mm) 130(W)×81(H)×99(D)
Mass Approx. 0.7kg

Performance Specification

Item Specification
Converter model VS-5F-1 VS-5FD-1 VS-5FX-1
Applicable sensor VRE-P028,VRE-P062
Min. setting units 0.5°
Number of programs (Panel display) 1 8(0 ~ 7) 16
(0 ~ 15)
32
(0 ~ 31)
Number of switch outputs 24 24 40 24
Number of multi-dogs 10 times for each switch output (0 ~ 9)
Position data sampling time
(permissible speed)
0.176ms (900 r/min When ON / OFF range is 1 degree)
Switch output setting method Numerical setting from the panel or teaching
Setting value memory Non-volatile memories (FRAM)
Error detection Sensor power error, Sensor error , Memory error , No setting error , Setting impossible error , System error
Auxiliary functions Protected switch
Setting change
during operation
Current position value
(BCD, gray code
(720-division))
-
Binary speed output - Selectable between current position output and speed output Selectable between current position output and speed output
Timing pulse output
Motion detection switch Selectable between timing pulse and speed detection output Selectable between timing pulse and speed detection output Selectable between timing pulse and speed detection output
Switch output enable
Hysteresis
Exterminal origin set - -
Arbitrary pulse output
Current position HOLD -
Error cancel
Password
Communication function

Serial (RS-232C) communication (setting value saving or loading, monitoring, operation commands)

  • Connection by Mitsubishi-only protocol/MELSEC-A protocol
  • Connection with angle display unit (NDP) is also possible
  • Connection by OMRON-only protocol
  • Connection with touch panel is possible (VARIMONI)
Connection of
an external display unit
I/O connection -
Communication
connection
Max. sensor
cable length
Standard 100m
Robotic(RBT) 100m

I/O spcification

Item VS-5F-1 VS-5FD-1 VS-5FX-1 Description
Input
signals
Program No. - 3 points 4/5 points Inputs the exteral program No.
Current position HOLD - 1 point - Used to prevent the current position value from changing when controller reading occurs.
Current position HOLD or
external origin set
- - 1 point Input to prevent current position from changing or for origin setting.
Error cancel 1 point 1 point 1 point Input to cancel an error display.
Switch output enable 1 point 1 point 1 point Switch signal will be output only upon the input of this signal.
Output
signals
Switch output /
Arbitrary pulse output
24 points 24 points 40/24 points ON/OFF signal will be output based on the switch setting value, or pulse signal
will be output based on equally dividing a single rotation (division selectable from 1 ~ 360).
Timing pulse /
Motion detection switch
1 point 2 points 1 point 60, 180 or 360 pulse signals will be output per rotation, or ON/OFF signal will be output based on the speed setting value.
System ready 1 point 1 point 1 point Outputs when controller and sensor are functioning normally.
Program No. - 3 points 4/5 points The currently selected Program No. is output.
Current position value
(BCD, gray code
(720-division)) /
Speed Binary output
- 11 points 11 points Current position (3-digit BCD + 0.5-deg display) signal will be output, or rotational speed will be output in binary code.
Latch pulse - 1 point 1 point Outputs a timing signal which ensures that the current position is read in a stable condition.
Item Input specifications Item Output Specifications
Input signals Program No.
External origin set
Current position HOLD
Error cancel
Switch output enable
Output signals Switch output or arbitrary pulse
Program No. System ready
Motion detection switch or timing pulse Current position value (BCD, gray code (720-division)) or speed (binary)
latch pulse
Input circuit DC input, photo-coupler isolation Output circuit Transistor (open-collector), photo-coupler isolation
Input logic Negative logic Output logic Negative logic Negative logic Positive logic*1
Rated input voltage 24VDC Rated load voltage 24VDC(30VDC max.)
Rated input current 10mA(24VDC) Max. load current 100mA 100mA 10mA(24VDC)
ON voltage 10VDC or more Max. voltage
drop when ON
2.0V 1.5V 0.7V
OFF voltage 4 VDC or less

*1 : The output logic for current position and speed can be changed through parameter setting.

============================================

For more product, click here.

STC Vietnam - Agent of NSD, provide NSD – VS-5FXT-1 – Controller VARICAM 

Contact us - SONG THANH CONG TRADING CO., LTD with the best support

Ms. Trinh

Tel: +84915 159944

Email: stc1@stc-vietnam.com

Skypee: stc1@stc-vietnam.com